Faculty Profiles - TADA Naoya

Papers - TADA Naoya

Division display 21 - 40 of about 154 ／ All the affair displays >>

Prediction of the Fracture Location by Tensile Tests of Gray Cast Iron Based on the Dimensional Changes of Graphite Flakes Reviewed

Naoya Tada, Takeshi Uemori, Junji Sakamoto

Journal of Pressure Vessel Technology 143 ( 2 ) 2021.4

Microscopic deformation of thin sheet of polycrystalline pure titanium under tension Reviewed

Naoya Tada, Kentaro Kishimoto, Takeshi Uemori, Junji Sakamoto

American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP 3 PVP2020-21715 2020.10

Finite element study of the effect of internal cracks on surface profile change due to low loading of turbine blade Reviewed

Junji Sakamoto, Naoya Tada, Takeshi Uemori, Hayato Kuniyasu

Applied Sciences (Switzerland) 10 ( 14 ) 4883 2020.7

短繊維強化複合材料の可視化データによる破壊予測技術 Reviewed

多田直哉

プラスチックエージ 66 ( 799 ) 53 - 56 2020.3

Analysis of the change of direct current potential difference and diameter distribution of thin pure titanium wire subjected to tensile and fatigue loads for fracture prediction Reviewed

SAKAMOTO Junji, TAKAGI Yusuke, UEMORI Takeshi, TADA Naoya

Transactions of the JSME (in Japanese) 86 ( 882 ) 19-00351 2020.2

Language：Japanese Publishing type：Research paper (scientific journal) Publisher：The Japan Society of Mechanical Engineers

<p>Pure titanium thin wires have been used for medical fields. It is important to investigate the possibility of non-destructive inspection of pure titanium thin wires for the safety utilization of them. In order to investigate a fracture prediction method for a pure titanium thin wire, we performed tensile and fatigue tests and a finite element analysis to analyze the changes of direct current potential difference and diameter distribution of the pure titanium thin wire during tensile and fatigue tests. It was found that a direct current potential difference method may be available for evaluating the tensile and fatigue damages of the pure titanium thin wire. In the tensile and fatigue tests, the normalized direct current potential difference increased almost linearly with an increase in the nominal strain, and a sign of an increase of the normalized direct current potential difference was observed when the fatigue crack propagated. Therefore, the nondestructive inspection could be conducted by setting a tolerance value of the normalized direct current potential difference, or detecting a sign of an increase in the normalized direct current potential difference. In addition, a method of predicting the fracture location from the diameter distribution change of the pure titanium thin wire was studied. The method could be applied to tensile and fatigue fractures.</p>

DOI： 10.1299/transjsme.19-00351

CiNii Article

researchmap

積層セラミックコンデンサのプレス変形挙動 Reviewed

成瀬文雄, 多田直哉

FCレポート，日本ファインセラミックス協会 38 ( 1 ) 30 - 34 2020.1

Slip Deformation of Crystal Grains in Semi-Circular Notched Thin Sheet Specimen of Pure Titanium during Tensile Test Reviewed

Takashi Ishida, Naoya Tada, Takeshi Uemori, Junji Sakamoto

Proceedings of the International Conference on Advanced Technology in Experimental Mechanics 2019 (ATEM ‘19) ( 19-402 ) 2019.10

Effect of Lubrication and Forging Load on Surface Roughness, Residual Stress, and Deformation of Cold Forging Tools Reviewed

Karunathilaka, Tada, Uemori, Hanamitsu, Fujii, Omiya, Kawano

Metals 9 ( 7 ) 783 - 783 2019.7

Language：English Publishing type：Research paper (scientific journal) Publisher：MDPI AG

Cold forging is a metal forming that which uses localized compressive force at room temperature. During the cold forging process, the tool is subjected to extremely high loads and abrasive wear. Lubrication plays an important role in cold forging to improve product quality and tool life by preventing direct metallic contact. Surface roughness and residual stress also greatly affects the service life of a tool. In this study, variations in surface roughness, residual stress, and specimen deformation with the number of cold forging cycles were investigated under different forging conditions. Specimens that were made of heat-treated SKH51 (59–61 HRC), a high-speed tool steel with a polished working surface, were used. The specimens were subjected to an upsetting process. Compressive residual stress, surface roughness, and specimen deformation showed a positive relationship with the number of forging cycles up to a certain limit and became almost constant in most of the forging conditions. A larger change in residual stress and surface roughness was observed at the center of the specimens in all the forging conditions. The effect of the magnitude of the forging load on the above discussed parameters is large when compared to the effect of the lubrication conditions.

DOI： 10.3390/met9070783

researchmap

Prediction of Fracture Location in Tensile Test of Short-Fiber-Self-Reinforced Polyethylene Composite Plates Reviewed

Naoya Tada, Ming Jin, Takeshi Uemori, Junji Sakamoto

Conference Papers, ASME 2019 Pressure Vessels and Piping Conference (PVP2019) PVP2019-93546 2019.7

Authorship：Lead author Language：English Publishing type：Research paper (international conference proceedings) Publisher：American Society of Mechanical Engineers

<title>Abstract</title>
Composite materials such as carbon-fiber-reinforced plastics (CFRP) and glass-fiber-reinforced plastics (GFRP) have been attracting much attention from the viewpoint of lightweight solution of automobiles and airplanes. However, the recyclability of these composite materials is not sufficient and the environmental load is large. Recently, self-reinforced polymer (SRP), in which similar polymer is used for reinforcing fibers and matrix, has been proposed. High-density polyethylene (HDPE) reinforced with ultra-high-molecular-weight polyethylene (UHMWPE) fibers, so-called self-reinforced PE (SRPE), is one of the promising thermoplastic composites. In this study, SRPE plates were made and the tensile tests were carried out. After the effect of reinforcement of UHMWPE fibers was evaluated on the basis of the tensile strength, the relationship between the distribution of UHMWPE fibers and the location of the final fracture line was examined. It was found from these experimental results that the fracture tends to occur along the regions with low area fraction of fibers or along those with low area fraction of fiber/matrix boundaries. This fact suggests that the fracture location of SRPs is predictable from the distribution of reinforcing fibers.

DOI： 10.1115/pvp2019-93546

researchmap

Crystal Plasticity Finite Element Analysis of Effects of Microscopic Non-Uniform Deformation on Surface Roughness of Pure Titanium Sheet Reviewed

Takeshi UEMORI, Hiroki KAKIHARA, Naoya TADA

Journal of the Society of Materials Science, Japan 68 ( 6 ) 478 - 484 2019.6

Microscopic Elastic and Plastic Inhomogeneous Deformations and Height Changes on the Surface of a Polycrystalline Pure-Titanium Plate Specimen under Cyclic Tension Reviewed

Naoya Tada, Takeshi Uemori

Applied Sciences 8 ( 10 ) 1907 - 1907 2018.10

Authorship：Lead author,　Corresponding author Language：English Publishing type：Research paper (scientific journal) Publisher：MDPI AG

A cyclic tensile test was carried out using a plate specimen of commercial pure titanium on a digital holographic microscope stage. Microscopic deformation of the grains was observed, and their height distribution was measured on the specimen surface. Each grain showed nanoscopic movement up and down, as well as reverse movement corresponding to specimen loading and unloading. We suggest that the different grain-specific changes in height were caused by microscopic inhomogeneities in the material, such as differences in the crystal orientation and geometries of both the surface and subsurface grains. Changes in grain height increased with tensile load, and a strong relationship was found between the height changes that occurred under elastic and plastic conditions. This suggests that microscopic plastic deformation is predictable from microscopic elastic deformation. In order to investigate the plastic deformation of grains in more detail, slip-line angles were measured after the tensile test. We found slip lines with similar angles in neighboring grains, suggesting that the plastic deformation of grains was not independent, but rather was related to that of surrounding grains and influenced by the deformation of subsurface grains.

DOI： 10.3390/app8101907

researchmap

Dimensional Changes of Graphite Flakes and Fracture in Tensile Tests of Gray Cast Iron Reviewed

Naoya Tada, Takeshi Uemori

Conference papers, ASME 2018 Pressure Vessels & Piping Conference PVP2018-85214 2018

Effect of Contact Pressure Applied on Tool Surface during Cold Forging on Fatigue Life of Tool Steel Reviewed

Nuwan Karunathilaka, Naoya Tada, Takeshi Uemori, Ryota Hanamitsu, Masahiro Kawano

Procedia Manufacturing 15 488 - 495 2018

Cyclic Stress Strain Resposes of AZ31 Magnesium Alloy Sheet Metal at Elevated Temperature Reviewed

Takeshi Uemori, Takashi Katahira, Tetsuo Naka, Naoya Tada, Fusahito Yoshida

Procedia Manufacturing 15 1792 - 1799 2018

Elastic and Plastic Microscopic Undulation on the Surface of Polycrystalline Pure Titanium under Tension Reviewed

Naoya Tada, Takeshi Uemori, Toshiya Nakata

Transactions of the ASME, Journal of Pressure Vessel Technology 139 ( 6 ) 061403 2017.12

Evaluation of Thin Copper Wire and Lead-Free Solder Joint Strength by Pullout Tests and Wire Surface Observation Reviewed

Naoya Tada, Takuhiro Tanaka, Takeshi Uemori, Toshiya Nakata

Crystals 7 ( 8 ) 255 - 255 2017.8

Springback analysis of aluminum alloy sheet metals by yoshida-uemori model Reviewed

Takeshi Uemori, Kento Fujii, Toshiya Nakata, Shinobu Narita, Naoya Tada, Tetsuo Naka, Fusahito Yoshida

Key Engineering Materials 725 566 - 571 2017

Time-Dependent Fracture of Copper-Cored Lead-Free Solder Ball and Nickel Rod Joints in Air, Distilled Water, and NaCl Solution Reviewed

Naoya Tada, Takeshi Uemori

IMPACT 2017 Proceedings 319 - 322 2017

Tensile Test of Copper-Cored Lead-Free Solder Joints Using Non-Contact Type Testing Device with Permanent Magnets Reviewed

N. Tada, T. Uemori, T. Nakata

SEM Annual 2017 Proceedings 478 - 478 2017

Theoretical predictions of fracture and springback for high tensile strength steel sheets under stretch bending Reviewed

Takeshi Uemori, Tetsuo Naka, Naoya Tada, Hidenori Yoshimura, Takashi Katahira, Fusahito Yoshida

Procedia Engineering 207 1594 - 1598 2017

　 PREV - NEXT 　

< TADA Naoya >

Papers - TADA Naoya